WixGear (2 Pack Universal Stick On Dashboard Magnetic Phone Car Mount, for Cell Phones and Mini Tablets with Fast Swift-snap Technology, (Newer Bigger Model)

If you have these type of mounts, you've tried them all. Comes with 3M adhesive with extra double sided tape. Comes with round and square plates.Magnets seem pretty strong. I suggest to do a test run before sticking plate on the inside of your phone case, make the hold will be strong enough. I have an OtterBox style case with a rubber sleeve. Seems to hold pretty good with the plate inside. Also the no slip texture of my case help with staying put on the phone mount. I rather mount on space below the window line on my dash than on top.Note: Pay attention to how you mount, if you want more of a downward position, mount with cable holder at the bottom.2 for 20.00 not a bad deal if you ask me.

Holds my S22 Ultra just fine, even on bumpy roads. I have a thin Ringke case and the metal plate is inside the case, holds with no problems!Couple of tips for the challenged ones out there...Double sided tape advice - CLEAN the surface you're mounting to. Grab some alcohol and paper towel and clean the spot until your towel is clean after wiping, the little included pad is a nice start, but all that stuff you wipe on your dash to make it shiny contains oils, waxes & silicone that are impossible to stick to, clean it! If it's cold outside, use a hairdryer to warm up the mounting spot and the adhesive after cleaning. If the mounting spot is really smooth or glossy, use a bit of fine grit sandpaper or green scotchbrite to scuff the small area up, this will give the adhesive something to grab onto. Wipe clean with alcohol after scuffing.Magnet to phone connection - The rubber pad on the mount provides friction and a grippy surface to keep the phone from sliding off, magnets alone are not strong enough to hold any phone in place. If the rubber gets dusty/dirty/oily there will not be enough grip to hold the phone in place and it will slide or vibrate off. Wipe it down occasionally with a damp cloth to remove any built up dust or residue.If your phone case is any thicker than a couple of business cards, you'll need to mount the metal plate on the outside. If your unsure, remove the case, place the metal plate between the case & phone (don't use the adhesive until you're sure it'll work) and reassemble, test the hold on the mount to determine if its strong enough for your needs.The only difficulty I had with adhesion was with the thin glue on the metal plate, it would not stick to my S22U, but I was unwilling to scuff up the back of my phone. A thicker tape might work better, but I found that the plate works just fine "loose" inside the case. YMMV.I really like the charging cable hook, keeps it close and tidy.The ball mount could use a bit more range or articulation, you might need to mount it upside down or sideways depending on your application.

Ordered these styles in the past and had multiple uses for cell phone use - mounting in the car dash board-to access easy cell phone use - at home in the bathrooms - kitchen- multiple use magnets are very strong and hold very good.

I mainly drive the highways and some construction sites, this mount holds my phone beautifully! Now if i was sending it off road this wouldn't be the mount id use. loved how it's rectangle, I used the rectangle phone plate in the middle of my phone so I can position my phone either way. The car mount has a creased mount so you can slightly curve it to your interior trim. Slightly bend at that crease, peel the double stick tape and press the mount where you need it. Not recommend for motorcycle use.

OK

The base that holds the entire stand together is a good inch wider than my last and it’s no longer feasible to put between the air conditioning switches in my 2017 Honda fit but it fit snug under the hazard lights. The adhesive is strong and the magnet is solid too. Great job good low price would buy again!

Installed a week ago and this is prefect for an uneven dashboard. A previous different brand mount failed within 2 years as it had a flat base. This WixGear mount with a flexible base fits perfectly. Just hope it lasts for a while. Will update this review if anything fails.

Great Looking. Did not work with my Magsafe case.